Ideal Standard Close Coupling Ring Washer Doughnut Toilet WC Cistern

Product Information

To stop water running out of the cistern through these holes the fitting kit is supplied with 2 conical rubber washers. The thinnest end plugs down into the hole and as the bolts are done up, a metal washer on top crushes the rubber into the hole creating a firm seal. Before doing anything, the first task is to turn off the water supply to the cistern so that you can safely disconnect the flexi hose or other means of connection. This is the most likely root of the cause, however there can be others so read on to learn about how to resolve leaks with close coupled toilets. Why is my Close Coupled Toilet Leaking When I Flush??

If these rubber seals are not installed correctly and aren’t actually creating the required seal they’re supposed to, no matter how slight a gap there is, water can easily leak down through. The close coupled toilet is a fairly modern iteration and was meant as a replacement for the older and less efficient low level toilet. This is a problem in itself as the two types of toilet suite are very rarely interchangeable due to their size and layout. To see how to get over this problem go to our project on changing toilets Note: There are several different sizes of doughnut so make sure that you get the right one. Measure the diameter of the base of the flush valve in the cistern and then you will know what size doughnut you need to ensure it fits correctly. If however you find that you still have a leak then you will need to remove the cistern again and apply some Plumbers Mait all around the doughnut, top and bottom. Once reassembled this should now fully resolve any leaks. If you have ever seen an old and aged piece of rubber then you will know that it looses it’s flexibility and essentially dries out and becomes brittle. At this point it will have lost it’s ability to form a decent seal and will then start to leak.

Why is my Close Coupled Toilet Leaking When I Flush??

With everything cleaned and ready refit, pop the brand new doughnut down on top of the toilet cistern in it’s recess making sure that it is sitting correctly and flat on the toilet pan. Take off the cistern lid and disconnect the push button or similar flush mechanism and put the lid safely to one side. With the wall fixings removed the final job before removing the cistern is to loosen and remove the through bolts holding the cistern to the pan. Refit the 1 or 2 screws that secure the cistern to the surface behind but don’t tighten them too much, leave a little wiggle room. This is just to help hold everything in place and ensure nothing moves out of place. Note: If there is no isolation valve installed then now is an ideal time to install one. See our project on how to fit an isolation valve for help on how to do so.

Jeez!! Is it just me or did your eyes glaze over after the first few words of this lot?? You would think anyone that can write like that could afford to get a real Plumber to fix it!! Oh well, as I aways say, the educated poor eh!! However this issue would not just become apparent after flushing the toilet, there would be a constant leak. When screwing up these bolts once they are inserted down through the toilet pan, if you don’t tighten them evenly and together so that the cistern is pulled down straight and level then this can also be a cause of leaks as the cistern will sit at an angle and not seal the doughnut correctly. Other Causes of Leaks From Close Coupled ToiletsI know nothing about plumbing, but since I am a home owner, I thought I should start from somewhere. The sighon of our toilet is worn out and I am trying to replace it with a new one. The toilet is Ideal Standard M360, very old so I had to struggle to remove the bolts, wing nuts etc with some help from DW40. We are currently using Royal Mail Parcelforce and DPD as our delivery providers, all small items will be delivered by Royal Mail, these can take up to three working days to reach you. I realise this is an old thread however my experience may be useful to others. I also had a siphon fault with toilet marked M360 from Ideal Standard made in late 1995. I believe the model name is Reflections or Meadow and it was designed as a 7 litre flush. As the issue would also only present itself after the toilet is flushed then this could potentially appear as a failed seal between the cistern and pan. This would also coincide with a newly installed toilet. Again if this is a newly installed toilet and you have just noticed a puddle of water on the floor then it may be coming from the incoming water supply and where it’s attached to the toilet fill valve or flush valve as it’s also known.